Paccar ESA Electronic Service Analyst 5.6 :

Paccar ESA - Electronic Service Analyst 5 - программа для диагностики Kenworth и Peterbilt
Работает с Nexiq, CECU Emul, ICU Emul.

The Electronic Service Analyst (ESA) is a PC-based diagnostic tool similar to CAT ET or Cummins INSITE. ESA communicates over a Data Link Adapter to the NAMUX components. A technician can use ESA to detect fault codes in the components, verify and troubleshoot new electronic instrumentation functionality, flash the control unit, program parameters and diagnose the root cause of the problems using service information on DealerNet.

Overview
An update of ESA is available for download. It is identified as version 4.2.0.142 with a data version of 209

Changes Implemented
• Updated support for the following control units
o CECU3 for Next Generation Platform for the Peterbilt 587
 New software P30-1014-003
o CECU3 for 2013 Engine controller support
 New software P30-1031-005
 New software P30-1030-006
o PACCAR Display (Smart Nav / Nav Plus)
 New Software P30-6037-200
• Requires a minimum version of P30-6037-103
• Some CECU3 software is now downloadable
o P30-1014-003
• Monitor / Simulate
o New Limited interface message shown if CECU3 software is unknown, or not downloaded.
• Flashing and Restore parameters
o New Limited interface message shown if CECU3 software is unknown, or not downloaded.

New CECU3 software P30-1031-005
Supports the following new vehicle features:
o Engine Derate and Shutdown functionality
o Check Engine Light Update – MX no longer affected by EGR warnings
o Coolant CVSG Telltale Update – Telltale no longer responds to SPN111 FMI11
o HC Burn update – Now activate both parked and moving warnings
o Prevent Startup DTCs

Includes the following fixes:
o Resolved an issue regarding security levels of the re-allocated RAM. Allows ESA to access the new memory locations.
o Wildcard text updated to Connect Diagnostic Tool; this appears for unsupported Check/Stop Engine faults
o Updated default parameters
o MX HC Burn French translation updated
o Adaptive Cruise Disabled French translation updated
o Adaptive Cruise Not Available French translation updated
o Cruise Set Speed in area 4 no longer active when cruise is not activated
o Clock will now increment if set to 12am
o Clock will not increment if it was not set, but will broadcast a counter on VCAN if requested to give a valid TD(Time/Date) message.
o Addressed an issue with the TD (Time/Date) message on VCAN that was populating it with nonsensical data
o Fixed an error that prevented the Odometer from incrementing

New CECU3 software P30-1030-006
Supports the following new vehicle features:
o Engine Derate and Shutdown functionality
o Check Engine Light Update – MX no longer affected by EGR warnings
o Coolant CVSG Telltale Update – Telltale no longer responds to SPN111 FMI11
o HC Burn update – Now activate both parked and moving warnings

Includes the following fixes:
o Resolved an issue regarding security levels of the re-allocated RAM. Allows ESA to access the new memory locations
o Clock will now increment if set to 12am
o Clock will not increment if it was not set, but will broadcast a counter on VCAN if requested to give a valid TD(Time/Date) message
o Addressed an issue with the TD (Time/Date) message on VCAN that was populating it with nonsensical data
o Speedometer will now correctly receive the CCVS message (CCVS Source Address fixed to receive from engine)
o Fixed an error in the SOFT Message PGN settings on the Engine VCAN Input
o Fixed an error that prevented the Odometer from incrementing

New CECU3 software P30-1014-003
New Features:
o Support for remote keyless entry
o Expanded trip information
o Check engine lamp changes
o Derate and shutdown functionality
o Regeneration popup updates
o Hydrocarbon burn updates
o Retarder telltale updates
o Diesel exhaust fluid updates
o Greenhouse gas vehicle speed limiter functionality
o Greenhouse gas idle shutdown timer
o Digital speedometer in the display
o Ignition status sent to the door modules to properly control the window operation
o Electric air gauges functionality
Defect Fixes:

o ESA can control the speedometer and tachometer
o ESA can control cluster’s minor gauges
o ESA simulation mode does not longer cause sounds
o Cruise control does not longer get stucked after using cruise pause on MX engines
o Trip odometer rolls over at 6000 miles
o If the clock and alarm are disabled the set clock message is not displayed
o Dimmer buttons support push and hold functionality
o Better TFT backlight range
o Cruise control functionality via the steering wheel
o Cruise control switches in the steering wheel included in the rationality check
o Cruise control telltale activated by cruise on/off switch
o Warning text description does not longer quickly appears and disappears when moving and the warning screen is entered
o Vehicle following distance now supports three digit values
o Clock can be set to 12:00 AM (as well as any other time)
o Unit parameter properly controls displayed units
o Fuel economy bar graph properly displays information
o Reoccurrence of some warnings after suppression
o Warning and faults are shown from all the devices
o Headlamps left on warning is properly displayed

New PACCAR Display software P30-6037-200
New Features:
o System Info Screen for ESN’s and ID’s
o Steering Wheel Controls enabled (NAMUX 3.5 and 4 Only)
o New and Expanded Virtual Gauges
o Garmin Version 3.20
o VIN Discriminator for NAMUX 4 Trucks for Dead Reckoning
o Internet Browser Opera 10.1 /Modem Management (disabled by default)
o Updated Driver Distraction Mode for Display and Audio Settings
o Audio Amplifier Fault Message Pop-Up
o Software Patches for Flicker and Garmin ID

Known Issues:
• Microsoft .NET 4.5 prevents ESA from running
• ESA does not function correctly in Windows 8