---===SME_1304_00002_0001.djvu===--- Pub.No.00EHT0036, APRIL 2013 AUTOMATIC TRANSMISSION/ OUTRIGGER EQUIPPED USE ---===SME_1304_00002_0001.djvu===--- Pub.No.00EHT0036, APRIL 2013 AUTOMATIC TRANSMISSION/ OUTRIGGER EQUIPPED USE ---===SME_1304_00002_0002.djvu===--- GROUP INDEX 23 14 10 34B 26 35 52 54 55 MODIFICATION SUMMARY ............ ENGINE ............................................ COOLING ......................................... AUTOMATIC TRANSMISSION ........ FRONT AXLE ................................... REAR SUSPENSION <LEAF (TRUNNION TYPE)> ........... BRAKE ............................................. INTERIOR......................................... ELECTRICAL ................................... HEATER, AIR CONDITIONER ......... FOREWORD This Shop Manual is published for the information and guidance of personnel responsible for maintenance of Mitsubishi Fuso FP. FV series trucks, and includes proce- dures for adjustment and maintenance services. We earnestly look forward to seeing that this manual is made full use of in order to perform correct services with no wastage. As this Shop Manual is published as a supplement to the following Shop Manuals, please see the followings for in- formation not included in this manual. Diesel Engine I OM457 ............. .. Pub. No. 00EHT0001 Diesel Engine II OM457 .............. Pub. No. 00EHT0002 Chassis I FP. FS. FV ....... ............ Pub. No. 00EHT0003 Chassis II FP. FS. FV ...... ............ Pub. No. 00EHT0004 Electrical FP. FS. FV ............. ...... Pub. No. 00EHT0005 For more details, please consult your nearest authorized Mitsubishi Fuso dealer or distributors. Kindly note that the specifications and maintenance ser- vice figures are subject to change without prior notice in line with improvement which will be effected from time to time in the future. Applicable models FS. FV APRIL 2013 ©2013 Mitsubishi Fuso Truck & Bus Corporation Printed in Japan ---===SME_1304_00002_0003.djvu===--- 1 MODIFICATION SUMMARY ---===SME_1304_00002_0004.djvu===--- 2 1. Engine This section describes only the difference from OM457 (EURO V) Shop Manual diesel engine I (Pub.No.00EHT0011). Be sure to check the differences described in the following before servicing. Group Contents of different points Service procedure 10 The flex plate is added due to the introduction of Allison automatic transmission. See Gr10. 14 (1) Engine coolant capacity has been changed. (2) The oil cooler is added due to the introduction of Allison automatic transmission. (3) The surge tank is different. See Gr14. MODIFICATION SUMMARY ---===SME_1304_00002_0005.djvu===--- 3 2. Chassis This section describes only the difference from FP.FS.FV (EURO V) Shop Manual chassis I (Pub.No.00EHT0013). Be sure to check the differences described in the following before servicing. Group Contents of different points Application Service procedure 00 (1) The following models are added in "POWER TRAIN TABLE". -- Same as before except these explained here. 23 (1) Automatic transmission is added. Allison 4000 type transmission is now incorporated. FS See Gr23. 25 (1) A new propeller shaft configuration is added. FV54 Same as before except these explained here. (2) The 90° phase shift position for the propeller shaft connection is changed. 26 (1) The tread in "SPECIFICATIONS" is changed. (2) Wheel alignment is changed. (3) In "WHEEL HUB AND BRAKE DRUM", the knuckle retainer is added to the knuckle. All models See Gr26. 27 (1) There is a change in "SPECIFICATIONS" (Reduction, marked position). All models Same as before except these explained here. 34B (1) Stiffener is added to the radius rod bracket. FS See Gr34B. Vehicle model Engine Clutch Transmission Propeller shaft Front axle Rear axle Reduction & Differential FS52SS3FAA OM457T3 Torque converter M140A6 (Allison 4000) GW5E2200 /P12 F900T/ F900TR R10TT/ R10T D10H (T) FV51SSK3VDEA C12W43P G230-12 P140/P10 F900T FV54STK3VFAA Item Specifications Reduction Model D10H D10HT Type Single-reduction Tooth shape Hypoid gear Gear ratio 4.222 4.625 6.166 Installation: Propeller shaft On the following models, the propeller shaft specified in the illustration must be installed with a phase shift of 90°. <FV54STK> ---===SME_1304_00002_0006.djvu===--- 4 34C (1) There is a change in "SPECIFICATIONS" ( marked position). FV54 Same as before except these explained here. 35 (1) There are changes in the following items in "SPECIFICATIONS". Air tank Wheel brake (2) The brake system is changed. All models See Gr35. 52 (1) New type air suspension is added to the seat suspension. FS, FV54 See Gr52. (2) Wide type floor console for 2-person seating capacity model is added. FV54 55 (1) The tightening torque for condenser mounting nut is added. All models See Gr55. Group Contents of different points Application Service procedure Item Specifications Air spring (effective diameter × installed height) mm φ250 × 291 Leaf spring (length × width × thickness -- No. of leaves) mm (615+380)×80×35--2 ---===SME_1304_00002_0007.djvu===--- 5 3. Electrical This section describes only the difference from FP.FS.FV (EURO V) Shop Manual electrical (Pub.No.00EHT0015). Be sure to check the differences described in the following before servicing. Group Contents of different points Application Service procedure 54-00C STRUCTURE AND OPERATION Meter cluster is changed. All models See Gr54-00C. 54-01 POWER, CHARGE AND GROUND CIRCUIT (1) Some changes are made in "FUSE BOX". (2) Only the changed portions in " POWER CIRCUIT" are shown. (3) Only the changed portions in " GROUND" are shown. All models See Gr54-01. 54-03 LIGHTING CIRCUIT " BACKUP LAMP CIRCUIT" is changed. All models See Gr54-03. 54-04 METER CIRCUIT " SPEEDOMETER CIRCUIT" for automatic transmission is add- ed. FS See Gr54-04. 54-09 OTHER CIRCUIT " CRUISE CONTROL AND VEHICLE SPEED LIMITING CIR- CUIT" is changed. All models See Gr54-09. 54-10 ELECTRICAL EQUIPMENT INSTALLATION POSITIONS All the items are shown. All models See Gr54-10. 54-11 INSPECTION OF ELECTRICAL EQUIPMENT "#352 Inspection of pulse converter" is changed. All models See Gr54-11. 110 130 340 417 962 ---===SME_1304_00002_0008.djvu===--- 10-1 GROUP 10 ENGINE FLYWHEEL ......................................................................................... 10-2 For other details except the items described above, please see Shop Manual diesel engine I OM457 (EURO V) Pub.No.00EHT0011 GROUP 10 ENGINE. ---===SME_1304_00002_0009.djvu===---