---===SME_1303_00005_0001.djvu===---
Pub.No.00ELT0027, FEBRUARY 2013 
---===SME_1303_00005_0001.djvu===---
Pub.No.00ELT0027, FEBRUARY 2013 
---===SME_1303_00005_0002.djvu===---
GROUP INDEX 
MODIFICATION SUMMARY ............ 
GENERAL ........................................ 
FUEL AND ENGINE CONTROL ...... 
MANUAL TRANSMISSION.............. 
ANTI-LOCK BRAKE SYSTEM 
(ABS)................................................ 
STEERING <POWER STEERING 
(Except FB70)>................................ 
ELECTRICAL ................................... 
FOREWORD 
This Shop Manual is published for the information and 
guidance of personnel responsible for maintenance of 
Mitsubishi Fuso CANTER series truck, and includes pro- 
cedures for adjustment and maintenance services. 
We earnestly look forward to seeing that this manual is 
made full use of in order to perform correct services with 
no wastage. 
As this Shop Manual is published as a supplement to the 
following Shop Manuals, please refer to the followings for 
information not included in this manual. 
4D3 diesel engine ........................ Pub. No. TWDE0610 
CANTER chassis ..........................Pub. No. TWSE0611 
CANTER electrical ........................ Pub. No. THSE0604 
For more details, please consult your nearest authorized 
Mitsubishi Fuso dealer or distributors. 
Kindly note that the specifications and maintenance ser- 
vice figures are subject to change without prior notice in 
line with improvement which will be effected from time to 
time in the future. 
FEBRUARY 2013 
Applicable models 
FE, FG 
©2013 Mitsubishi Fuso Truck & Bus Corporation Printed in Japan 
---===SME_1303_00005_0003.djvu===---
1 
MODIFICATION SUMMARY 
---===SME_1303_00005_0004.djvu===---
2 
1. Engine 
This section describes only the differences from "4D3 Shop Manual diesel engine" (Pub.No. TWDE0610). 
Be sure to check the differences described in the following before servicing. 
Group 
Contents of different points 
Application 
Service 
procedure 
11 (1) In STRUCTURE AND OPERATION, the double (inner and outer) valve 
spring is changed to the single (outer only) valve spring. 
All models 
Same as 
before except 
these explained 
here. 
MODIFICATION SUMMARY 
---===SME_1303_00005_0005.djvu===---
3 
11 (2) In ROCKER COVER AND ROCKER CASE, the cylinder head cover and re- 
lated parts (marked with ) are not installed. 
All models 
Same as 
before except 
these explained 
here. 
Group 
Contents of different points 
Application 
Service 
procedure 
---===SME_1303_00005_0006.djvu===---
4 
11 (3) In CYLINDER HEAD AND VALVE MECHANISM, the inner valve springs are 
eliminated (only outer valve springs are used) and the standard values and 
limits are changed as shown below. 
Service standards 
All models 
Same as 
before except 
these explained 
here. 
13 (1) The service procedure for spare tank is added due to the addition of the 
spare tank. 
All models 
See Gr13. 
(2) In "FUEL FILTER", the tightening torque of the eyebolts is different. 
Same as 
before except 
these explained 
here. 
Group 
Contents of different points 
Application 
Service 
procedure 
Location 
Maintenance item 
Standard value 
Limit 
Remedy 
4 
Outer valve 
spring 
Free length 
68.3 
63.0 
Replace 
Installed load 
(47.25 in in- 
stalled length) 
390 ± 20N 
{40 ± 2.0 kgf) 
348 N 
{35.5 kgf} 
Squareness 
-- 
2.5 
MODIFICATION SUMMARY 
---===SME_1303_00005_0007.djvu===---
5 
14 (1) In the Service standards for RADIATOR, the check value for air leakage from 
radiator is different. 
Service standards 
FE8, FG8 
Same as 
before except 
these explained 
here. 
Group 
Contents of different points 
Application 
Service 
procedure 
Location 
Maintenance item 
Standard value 
Limit 
Remedy 
14 
Air leakage from radiator 
(air pressure 177 kPa {1.8 kgf/ 
cm 
2 
}) 
0cm 
3 
{0 mL} 
-- 
Replace 
---===SME_1303_00005_0008.djvu===---
6 
2. Chassis 
This section describes only the differences from "CANTER Shop Manual chassis" (Pub. No. TWSE0611). 
Be sure to check the differences described in the following before servicing. 
Group 
Contents of different points 
Application 
Service 
procedure 
00 (1) New powertrain combination added. 
(2) Inspection procedure using diagnosis codes is changed. 
All models 
See Gr00. 
22 (1) The transmission mounting support is changed. 
Removal sequence 
FE85C-Z 
Same as 
before except 
these explained 
here. 
25 (1) The propeller shaft model applications to the vehicle models shown in "Spec- 
ifications" table are changed. 
All models 
Same as 
before except 
these explained 
here. 
1 Propeller shaft (See Gr25.) 
2 Parking brake cable (See Gr36.) 
3 Transmission 
* 
a: Transmission mounting support 
Item 
Specifications 
FE7, FG <Front axle> FE8, FG <Rear axle> 
Propellar shaft Model 
P2 
P3 
MODIFICATION SUMMARY 
---===SME_1303_00005_0009.djvu===---